Others

 

Others

Evolution Behavior of Shear Band in Al?0.5Mg?0.4Si?0.1Cu Alloy During Hot Compression Process
22/03/2024 - To clarify the evolution behavior of shear bands in Al?0.5Mg?0.4Si?0.1Cu alloy under high temperature conditions, isothermal compression tests were carried out under 400 °C, 450 °C, and 500 °C...
Mechanism of Cell-Killing Activity of Plantaricin LD1 Against Escherichia coli ATCC 25922
- Abstract Plantaricin LD1 was purified from a potential probiotic strain, Lactobacillus plantarum LD1 previously isolated from indigenous food, Dosa. In this...
A comprehensive study of dielectric, modulus, impedance, and conductivity of SrCeO3 synthesized by the combustion method
23/03/2024 - This demonstrates the successful synthesis of SrCeO3 perovskite materials using the solution combustion method (SCM). The X?ray diffraction (XRD) patterns of the prepared sample at different...
An applicability study on various methods for determining the monomer conversion rate of polyamide 6
22/03/2024 - The composite of PLA and untreated bamboo filler was fabricated in kneading at 180°C and injection molding at 150–175°C and 95?MPa for 1.5?s. The composite products containing PLA/BF at 50:50 and...
Combined Effects of Steel and Glass Fibres on the Fracture Performance of Recycled Rubber Concrete
22/03/2024 - As an environmentally friendly construction material, recycled rubber concrete (RRC) is commonly used as a road material owing to its excellent flexural strength and crack resistance. Previous...
Enhancing Water Resistance and Mechanical Properties of Cemented Soil with Graphene Oxide
22/03/2024 - Although cemented soil as a subgrade fill material can meet certain performance requirements, it is susceptible to capillary erosion caused by groundwater. In order to eliminate the hazards caused by...
Rheological Performance Analysis of Different Preventive Maintenance Materials in Porous High-Viscosity Asphalt Pavements
22/03/2024 - Porous asphalt pavements are widely used in rainy and wet areas for their skid resistance, noise reduction, runoff minimization and environmental sustainability. Long-term moisture vapor erosion and...
The Properties of High-Performance Concrete with Manganese Slag under Salt Action
25/03/2024 - Manganese slag (MS) containing a certain amount of active hydration substances may be used as a kind of cementitious material. In the present study, we measured the mass, the relative dynamic modulus...
The Effect of Processing Conditions on the Microstructure of Homopolymer High-Density Polyethylene Blends: A Multivariate Approach
22/03/2024 - In this work, a multivariate approach was utilized for gaining some insights into the processing–structure–properties relationships in polyethylene-based blends. In...
Enhancing Rubber Vulcanization Cure Kinetics: Lowering Vulcanization Temperature by Addition of MgO as Co-Cure Activator in ZnO-Based Cure Activator Systems
22/03/2024 - Vulcanization is a chemical modification of rubber that requires a considerable amount of thermal energy. To save thermal energy, the kinetics of rubber vulcanization should be improved. In this...
Characterization of Polylactic Acid Biocomposites Filled with Native Starch Granules from Dioscorea remotiflora Tubers
25/03/2024 - Biocomposites were fabricated utilizing polylactic acid (PLA) combined with native starch sourced from mountain’s yam (Dioscorea remotiflora Knuth), an underexplored tuber variety....
Fabrication of robust polyamide 6 with local cross?linked structure via dynamic vulcanization
21/03/2024 - The mechanical properties of toughened PA6.Polyamide 6 (PA6) is a widely used thermoplastic engineering polymer, and the toughening modification for PA6 is always a main research topic. Meanwhile,...
Salt?Assisted Vapor–Liquid–Solid Growth of 1D van der Waals Materials
19/03/2024 - The method of salt?assisted vapor–liquid–solid (VLS) growth is introduced to synthesize 1D nanostructures of trichalcogenide van der Waals (vdW) materials, exemplified by niobium trisulfide...
Preparation of transparent electrospun nanofibrous membrane from long?persistent phosphor?reinforced polymer for security authentication
17/03/2024 - Eggshell processing produced an ecologically based additive, with great potential for manufacturing biopolyethylene matrix composites.AbstractLow?density biopolyethylene (BioLDPE) ecocomposites added...
SMA/PUA based double-layer thermo-expandable microcapsules and their performances
21/03/2024 - Abstract In this study, the double-layered thermo-expandable microcapsules with n-hexane as the core and styrene maleic anhydride copolymer (SMA) / polyurea (PUA) as...
Control of Meniscus Formation Using an Electrohydrodynamics Module in Roll-to-Roll Systems for the Stable Coating of Functional Layers
19/03/2024 - In fabricating functional layers, including thin-film transistors and conductive electrodes, using roll-to-roll (R2R) processing on polymer-based PET film, the instability of the slot-die coating...
Development of a Polypropylene-Based Material with Flame-Retardant Properties for 3D Printing
21/03/2024 - In this study, a nanocomposite based on a heterophasic polypropylene copolymer containing 5 wt% of nanoclays and 3 wt% of compatibilizer was formulated via melt compounding to obtain a material...
Influence of Interfacial Interaction and Composition on Fracture Toughness and Impact Properties of Carbon Fiber-Reinforced Polyethersulfone
21/03/2024 - In this study, the interlaminar fracture toughness and impact strength of polyethersulfone reinforced with continuous carbon fibers were studied. Interlaminar fracture toughness tests were performed...
New role of ionic liquid as accelerator activator in rubber compounds and its influence on curing and mechanical properties
18/03/2024 - Interaction of Ionic liquid in rubber compounds in presence of activator and accelerator.This study focuses on the effect of ionic liquids (ILs) on the cure characteristics and filler dispersion of...
Novel aminocoumarin derivatives against phytopathogenic fungi: design, synthesis and structure?activity relationships
18/03/2024 - Phytopathogenic fungi is the most devastating reason for the decrease of the agricultural production and food safety. To develop new fungicidal agents for resistance concerning, a novel series of...
3D printing of cyanate ester resins with interpenetration networks for enhanced thermal and mechanical properties
16/03/2024 - Development of a wet?spinning process for manufacturing of pure chitosan multifilament yarns from ionic liquids on a semi?industrial pilot scale with given processability on industrial textile...