Others

 

Others

Utilization of Silybum marianum extract as a high-performance natural antioxidant for polyethylene
20/02/2024 - Abstract In this study, Silybum marianum extract powder was introduced into low density polyethylene (LDPE) as a primary polyphenolic antioxidant via melt blending...
Effects of TPU on the mechanical properties, fracture toughness, morphology, and thermal analysis of 3D?printed ABS?TPU blends by FDM
20/02/2024 - In this paper, blends of ABS?TPU with two different weight percentages of TPU were prepared using fused deposition modeling technology. The effect of adding TPU on the fracture toughness of ABS and...
Effect of Rapeseed Imidazoline Addition on the Properties of Lab-Aged 35/50 Pen Grade Bitumen
22/02/2024 - For the successful reuse of old asphalt as reclaimed asphalt pavement (RAP) added to new bituminous mixtures, it is necessary to improve some of its properties. This can be attained, for example, by...
Influence of Specimen Dimension, Water Immersion Protocol, and Surface Roughness on Water Sorption and Solubility of Resin-Based Restorative Materials
21/02/2024 - The evaluation of water sorption and solubility is pivotal for the development of new resin-based restorative materials with the potential for clinical application. The purpose of the present study...
Preparation, Microstructure and Thermal Properties of Aligned Mesophase Pitch-Based Carbon Fiber Interface Materials by an Electrostatic Flocking Method
21/02/2024 - The mesophase pitch-based carbon fiber interface material (TIM) with a vertical array was prepared by using mesophase pitch-based short-cut fibers (MPCFs) and 3016 epoxy resin as raw materials and...
Exploring the Effect of Cetylpyridinium Chloride Addition on the Antibacterial Activity and Surface Hardness of Resin-Based Dental Composites
21/02/2024 - The aim of this study was to evaluate the effect of cetylpyridinium chloride (CPC) addition on the antibacterial and surface hardness characteristics of two commercial resin-based dental composites...
Evaluation of effect of boric acid on thermoplastic starch: Morphological, mechanical, barrier, and optical properties
20/02/2024 - In this text, determination of structural, physical and mechanical properties of thermoplastic starch?boric acid films.In this study, starch was modified with different amounts of boric acid, and the...
Microwave curing of modified benzoxazine resin/ethylene–propylene–diene monomer rubber/Kevlar composite
20/02/2024 - Comparison of thermal and microwave curing of the BZ/EPDM/Kevlar thermal composite.The purpose of this paper was to show how modified benzoxazine resin/ethylene–propylene–diene monomer...
Study on the preparation of porous polyethylene glycol terephthalate film and the influencing factors of etching rate
21/02/2024 - The optimal etching conditions and the etching rate for preparing cylindrical pores on PET films.Porous polyethylene glycol terephthalate (PET) film is a kind of mesopore structure template with pore...
Preparation of Siloxane-Modified DOPO Flame Retardant Sol–Gel and Its Study on Flame Retardant PET Fabrics
21/02/2024 - Abstract In order to improve the flame retardant and anti-melt-drip performance of PET fabrics in an environmentally friendly and simple way, two transparent...
Preparation of Porous TiO2/PVDF/CA Fibers for Photocatalytic Degradation of Dyes by Centrifugal Spinning
16/02/2024 - A facile method for the preparation of porous micro/nano fibers was demonstrated. The TiO2/PVDF/CA-composite micro/nano fibers were prepared by centrifugal spinning and then CA was removed by a...
High temperature and fire properties of sustainable syntactic foam reinforced by end?of?life tyre?derived rubber particles
15/02/2024 - The management of end?of?life tyres faces challenges due to insufficient recycling infrastructure and technologies, as well as limited markets for the materials recovered from them. To mitigate this,...
Facile construction of polypyrrole microencapsulated ??Fe2O3 for simultaneously enhancing the flame retardancy and smoke toxicity suppression of intumescent flame?retardant epoxy resins
17/02/2024 - Fracture behavior of toughened polymethacrylate/polyurethane.AbstractAmorphous polymer/crystalline polymer blends can be prepared via the simultaneous polymerization of polymethacrylate/polyurethane...
Corrosion Behavior of Aluminum Alloys in Different Alkaline Environments: Effect of Alloying Elements and Anodization Treatments
19/02/2024 - Aluminum alloys are extensively used to manufacture mechanical components. However, when exposed to alkaline environments, like lubricants, refrigerants, or detergents, they can be corroded, reducing...
Fabrication and Characterization of Diaphragm Headphones Based on Graphene Nanocomposites
17/02/2024 - The goal of this paper is to fabricate innovative diaphragm headphones using graphene oxide paper (GOP) and GOP/epoxy nanocomposites (GOPC). Initially, graphene oxide suspension is fabricated, and...
Exploring Novel Applications for Hydrogels Derived from Modified Celluloses
16/02/2024 - The valorization of lignocellulosic biomass by-products holds significant economic and ecological potential, considering their global overproduction. This paper introduces the fabrication of a novel...
Flame-Retardant Thermoplastic Polyether Ester/Aluminum Butylmethylphosphinate/Phenolphthalein Composites with Enhanced Mechanical Properties and Antidripping
18/02/2024 - Aluminum butylmethylphosphinate AiBMP as a flame retardant and phenolphthalein as a synergistic agent were applied in a thermoplastic polyester elastomer (TPEE)) in the current study. The thermal...
Mechanisms Underlying a Quantum Superposition Microscope Based on THz-Driven Coherent Oscillations in a Two-Level Molecular Sensor
- We report pump-probe measurements of a hydrogen molecule (H2) in the tunnel junction of a scanning tunneling microscope coupled to ultrashort terahertz (THz) pulses. The coherent oscillation of the...
Unraveling the Highly Plastic Behavior of ALD?Aluminum Oxide Encapsulations by Small?Scale Tensile Testing
13/02/2024 - This article presents a systematic study on intentionally induced highly plastic flow in amorphous Al2O3 coatings. In?situ transmission electron microscopy tensile experiments showcase the plastic...
Tomography of Laser Powder Bed Fusion Maraging Steel
15/02/2024 - The presence of defects in additive manufactured maraging steel is a widespread problem as its dependence on processing parameters significantly influences it. Using X-ray computed tomography, along...