Materials
Materials
ISO 3671:2023 - Plastics — Aminoplastic moulding materials — Determination of volatile matter
-
This document specifies a method for the determination of volatile matter (predominantly water) in aminoplastic moulding materials, by drying in an oven.
ISO 60:2023 - Plastics — Determination of apparent density of material that can be poured from a specified funnel
-
This document specifies a method of determining the apparent density, i.e. the mass per unit of volume, of loose material (powder or granular material) that can be poured from a funnel of...
ISO 61:2023 - Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel
-
This document specifies a method of determining the apparent density, i.e. the mass per unit of volume, of loose material that cannot be poured from a funnel of specified...
ISO 24187:2023 - Principles for the analysis of microplastics present in the environment
-
This document describes the principles to be followed in the analysis of microplastics in various environmental matrices. This includes the unique particle size classification of plastics, the...
ISO 9854-2:2023 - Thermoplastics pipes for the transport of fluids — Determination of Charpy impact properties — Part 2: Test conditions for pipes of various materials
-
This document specifies the values or options chosen for the test parameters (i.e. the impact energy, specimen dimensions, specimen type, specimen supports and test temperature) for both...
ISO/TS 10818:2023 - Nanotechnologies — Textiles containing nanomaterials and nanostructures — Superhydrophobic characteristics and durability assessment
-
This document specifies the characteristics and performance(s) of the superhydrophobic textiles containing nanomaterials and nanostructures (TCNNs) based on contact angle measurement before and...
ISO/ASTM 52924:2023 - Additive manufacturing of polymers — Qualification principles — Classification of part properties
-
This document establishes the required or the achievable classes of part properties for additive manufactured polymer parts in order to get a common understanding on part quality. It is aimed...
ISO/TS 10689:2023 - Nanotechnologies — Superhydrophobic surfaces and coatings: Characteristics and performance assessment
-
This document specifies requirements and recommendations for performance assessment methods for superhydrophobic surfaces and coatings subjected to mechanical stress, solar radiation and...
ISO 5425:2023 - Specifications for use of poly(lactic acid) based filament in additive manufacturing applications
-
This document specifies the technical requirements, test methods, detection rules, marking/labelling, packaging, transportation and storage of poly(lactic acid) (PLA) based filament for use in...
ISO 7231:2023 - Polymeric materials, cellular, flexible — Determination of air flow value at constant pressure-drop
-
This document specifies two methods for determining the air flow value of flexible cellular polymeric materials:— method A, for conventional types of flexible cellular...
ISO 14932:2023 - Rubber compounding ingredients — Organic vulcanizing agents — Determination of organic peroxide content
-
This document specifies four methods for the determination of the content of the following groups of organic peroxides used as rubber vulcanizing agents. There are three titration methods and...
ISO/ASTM 52902:2023 - Additive manufacturing — Test artefacts — Geometric capability assessment of additive manufacturing systems
-
This document covers the general description of benchmarking test piece geometries, i.e. artefacts, along with quantitative and qualitative measurements to be taken on the benchmarking test...
ISO 8124-6:2023 - Safety of toys — Part 6: Certain phthalate esters
-
This document specifies a method standard for the determination of di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl-butyl phthalate (BBP), bis-(2-ethylhexyl)...
ISO 10468:2023 - Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions
-
This document specifies methods for determining the ring creep properties for glass-reinforced thermosetting plastics (GRP) pipes. Properties include the creep factor and the long-term creep...
ISO/TS 23690:2023 - Nanotechnologies — Multiwall carbon nanotubes — Determination of carbon impurity content by thermogravimetric analysis
-
This document specifies a mild oxidation method to determine the content of carbon impurities (carbon material content not in the form of CNT, including amorphous carbon and trace amountd of...
ISO 11235:2023 - Rubber compounding ingredients — Sulfenamide accelerators — Test methods
-
This document specifies the methods to be used for the evaluation of sulfenamide accelerators:— MBTS: benzothiazyl disulphide;— CBS:...
ISO 11424:2023 - Rubber hoses and tubing for air and vacuum systems for internal-combustion engines — Specification
-
This document specifies requirements for rubber hoses and tubing for use in the various air and vacuum systems found on internal combustion engines. This document does not cover hoses used for...
ISO 4410:2023 - Test methods for the experimental characterization of in-plane permeability of fibrous reinforcements for liquid composite moulding
-
This document specifies test methods for the experimental characterization of in-plane permeability of fibrous reinforcements for liquid composite moulding. Requirements for test equipment,...
ISO 4768:2023 - Measurement method of anti-biofilm activity on plastic and other non-porous surfaces
-
This document specifies a test method to evaluate the anti-biofilm activity of anti-biofilm treated plastics and other non-porous surfaces of products, including intermediate products. It is...
