Materials
Materials
Influence of Metal Surface Structures on Composite Formation during Polymer–Metal Joining Based on Reactive Al/Ni Multilayer Foil
25/04/2024 -
During hybrid thermoplast metal joining with reacting Al/Ni foils, the structured metal surface influences crack initiation within the multilayer. Molten plastic penetrates the foil interface and...
Improve the thermal properties of oil?loaded polysulfone microcapsules by optimizing copper layer for self?lubricating polyamide
27/04/2024 -
Preparation process PAO@PSF/Cu microcapsules and tribological properties of PA6 composites.This work reports polymer/metal double?shell microcapsules with polysulfone (PSF) and copper as walls for...
The Influence of Surface Texture of Elements Made of PA6-Based Composites on Anti-Graffiti Effect of Paint Coating
23/04/2024 -
The aim of the work was to investigate the influence of the surface texture of composite based on PA6, intended for wet painting, on the stability of the colour and gloss parameters. The stability of...
Inspection of microwave self?healing efficiency in carbon nanotube reinforced polymer composites for aerospace applications
22/04/2024 -
Composite manufacturing steps and self healing phenomenon.The aerospace industry is evolving very rapidly every day, and due to the low operational and maintenance costs, unmanned aerial vehicles...
Compatibilization of Polyamide 6/Cyclic Olefinic Copolymer Blends for the Development of Multifunctional Thermoplastic Composites with Self-Healing Capability
18/04/2024 -
This study investigated the self-healing properties of PA6/COC blends, in particular, the impact of three compatibilizers on the rheological, microstructural, and thermomechanical properties. Dynamic...
Regression analysis for the determination of microplastics in sediments using differential scanning calorimetry
15/04/2024 -
This research addresses the growing need for fast and cost-efficient methods for microplastic (MP) analysis. We present a thermo-analytical method that enables the identification and...
An Investigation of Verbascum thapsus Flower as a Natural Source for Nylon 6 Fabric Dyeing
09/04/2024 -
With the rise of global demand for eco-friendly alternatives and the drive toward reducing the adverse environmental impact, the exploration of new sources of natural dyes has gained significant...
Influence of Strong Shear Field on Structure and Performance of HDPE/PA6 In Situ Microfibril Composites
10/04/2024 -
As one of the most widely applied general-purpose plastics, high-density polyethylene (HDPE) exhibits good comprehensive performance. However, mechanical strength limits its wider application. In...
Recycled PET/PA6 Fibers from Waste Textile with Improved Hydrophilicity by In-Situ Reaction-Induced Capacity Enhancement
11/04/2024 -
Due to the increasing amounts of textile waste, textile to textile recycling is of prime concern. Polyethylene terephthalate (PET) represents the most extensively used type of chemical fiber. Its...
Comparison of mechanical and tribological properties of glass-fiber-reinforced polyketone and polyketone/polyamide 6 blend composites
08/04/2024 -
In this study, the impact of two compatibilizers, ethylene terpolymer (C1) and maleic anhydride grafted polyethylene (C2), on the mechanical, thermal, and tribological properties of 30%...
Cement Mortars Based on Polyamide Waste Modified with Fly Ash from Biomass Combustion—A New Material for Sustainable Construction
08/04/2024 -
The article presents an analysis of the possibility of using the waste of polyamide 6 modified with fly ash (in the amount of 5, 10 and 15%) from the burning of wood–palm kernel shells...
Development of single?stream resin transfer molding using in?situ anionic polymerization of ??caprolactam with preprocessing on carbon fibers
05/04/2024 -
Manufacturing process and mechanical property enhancements using single?stream T?RTM and surface treatment of carbon fibers.Thermoplastic resin transfer molding (T?RTM) is one of the composites...
Insights on the processing and thermal degradation kinetics of PA6/PE?g?AA blends
27/03/2024 -
Tragacanth gum/Carrageenan/Clove Essential Oil biodegradable fimls: Antibacterial Properties.AbstractBiodegradable films have been developed to tackle the problem of environmental pollution caused by...
A low pollution surface pretreatment of PC?ABS under acidic conditions
21/03/2024 -
Applicability evaluation of various methods for determining monomer conversion rate of PA6 products prepared by anionic polymerization.AbstractAnionic ring opening polymerization of ??caprolactam...
Advance Analysis of the Obtained Recycled Materials from Used Disposable Surgical Masks
29/03/2024 -
The production of personal protective equipment (PPE) has increased dramatically in recent years, not only because of the pandemic, but also because of stricter legislation in the field of Employee...
Investigation on the Correlation between Biaxial Stretching Process and Macroscopic Properties of BOPA6 Film
01/04/2024 -
Biaxially oriented polyamide 6 (BOPA6) films were prepared by extrusion casting and biaxial stretching with polyamide 6. The effects of different biaxially oriented on the macroscopic properties of...
Application of machine learning methods in the analysis of interface bonding strength for overmolded hybrid thermoset?thermoplastic composites
29/03/2024 -
The process of establishing the healing degree model and six machine learning models.The focus of this study is to apply finite element method (FEM) and machine learning methods to investigate the...
Investigation of microstructural and mechanical properties of weld lines in injection?molded short glass fiber?reinforced polyamide 6
30/03/2024 -
Exploring the microstructure and mechanical strength of weld lines in injection?molded short glass fiber?reinforced polyamide 6.This research investigates the impact of weld lines on the mechanical...
pH?Responsive itaconic acid?based villous?like hydrogels for water?plugging materials
27/03/2024 -
Thermogravimetric analysis coupled to infrared plots of (a) PA6, (b) PE?g?AA, (c) PA6/PE?g?AA 90/10, (d) PA6/PE?g?AA 80/20, and (e) PA6/PE?g?AA 70/30 at 10°C/min.AbstractBlends of polyamide 6 (PA6)...
Quality Assessment of Socks Produced from Viscose and Lyocell Fibers
28/03/2024 -
Most casual socks are produced from cotton and are usually combined with synthetic fibers. The suitability of viscose and lyocell fibers for knitting socks needs to be investigated further....
