Materials
Materials
ISO 15527:2022 - Plastics — Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) — Requirements and test methods
-
This document specifies the requirements and test methods for solid flat compression-moulded sheets of polyethylene (PE-UHMW and PE-HD, see ISO 1043-1) without fillers or reinforcing...
F2737 Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units has been reapproved, available as F2737-11(2021)
-
1. Scope 1.1Â This specification covers materials, structural design, physical dimensions and manufacturing requirements for monolithic or sectional corrugated high...
ISO 14632:2021 - Extruded sheets of polyethylene (PE-HD) — Requirements and test methods
01/05/2021 -
This document specifies the requirements and test methods for solid flat extruded sheets of polyethylene homopolymers (PE-HD) without fillers or reinforcing materials.This document is...
F3202 Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Polypropylene (PP) Piping has been revised to F3202-19a
-
1. Scope 1.1 This specification covers requirements and test methods for 6 in. (150 mm) through 60 in. (1500 mm) fabricated or molded solid wall poly(vinyl...
F3202 Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Polypropylene (PP) Piping is a new standard now available. F3202-19
-
1. Scope 1.1 This specification covers requirements and test methods for 6 in. (150 mm) through 60 in. (1500 mm) fabricated or molded solid wall poly(vinyl...
F2649 Standard Specification for Corrugated High Density Polyethylene (HDPE) Grease Interceptor Tanks has been reapproved, available as F2649-14(2019)
-
Abstract This specification covers the material, design, structural performance, and manufacturing practice requirements for monolithic or sectional corrugated high density...
ISO 15527:2018 - Plastics -- Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) -- Requirements and test methods
-
This document specifies the requirements and test methods for solid flat compression-moulded sheets of polyethylene (PE-UHMW and PE-HD, see ISO 1043-1) without fillers or reinforcing materials....
F2487 Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines has been reapproved, available as F2487-13(2017)
-
Significance and Use 5.1 This is not a routine test. The values recorded are applicable only to the pipe being tested and at the time of...
F2737 Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units has been reapproved, available as F2737-11(2017)
-
1. Scope 1.1 This specification covers materials, structural design, physical dimensions and manufacturing requirements for monolithic or sectional corrugated high...
F2160 Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) has been revised to F2160-16
-
Abstract This specification covers material, dimensional, workmanship and performance requirements for polyethylene conduit, duct and innerduct manufactured for use in a...
D3485 Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) has been reinstated as D3485-15
-
1. Scope 1.1 This specification covers cable in conduit (CIC), which is a smooth-walled, coilable, high-density polyethylene (HDPE) conduit (duct) that contains...
F2649 Standard Specification for Corrugated High Density Polyethylene #40;HDPE#41; Grease Interceptor Tanks has been revised to F2649-14
-
Abstract This specification covers the material, design, structural performance, and manufacturing practice requirements for monolithic or sectional corrugated high density...
F2487 Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines has been revised (with title change) to F2487-13
-
Significance and Use 5.1 This is not a routine test. The values recorded are applicable only to the pipe being tested and at the time of testing....
